diff --git a/Configure/Printer.cfg/2WD_300_Model_TMC2240.cfg b/Configure/Printer.cfg/2WD_300_Model_TMC2240.cfg
index 3fd6d36..14dca12 100644
--- a/Configure/Printer.cfg/2WD_300_Model_TMC2240.cfg
+++ b/Configure/Printer.cfg/2WD_300_Model_TMC2240.cfg
@@ -808,34 +808,3 @@ gcode:
   RESPOND TYPE=command MSG='Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta'
   M117 "Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta"
 
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	-0.139892, -0.144629, -0.118855, -0.070701, -0.076458, -0.071339, -0.053576, -0.038063, -0.011182, -0.014896
-#*# 	-0.132548, -0.133431, -0.103451, -0.072262, -0.079405, -0.072497, -0.064156, -0.026437, 0.005466, 0.017700
-#*# 	-0.146372, -0.142454, -0.106913, -0.071101, -0.063307, -0.050075, -0.037609, -0.018205, 0.018473, 0.028662
-#*# 	-0.155715, -0.148744, -0.113136, -0.061509, -0.048525, -0.033687, -0.017161, 0.005627, 0.047608, 0.052961
-#*# 	-0.161258, -0.149702, -0.107886, -0.063084, -0.048428, -0.023841, -0.012515, 0.015900, 0.061648, 0.068628
-#*# 	-0.166502, -0.150839, -0.101034, -0.055136, -0.037974, -0.011766, 0.005559, 0.037965, 0.090939, 0.098797
-#*# 	-0.171896, -0.148182, -0.091620, -0.051904, -0.030924, 0.001613, 0.023529, 0.058473, 0.115695, 0.121967
-#*# 	-0.172872, -0.149272, -0.088044, -0.041005, -0.015835, 0.015057, 0.043967, 0.075708, 0.135351, 0.151476
-#*# 	-0.174137, -0.144846, -0.080953, -0.034735, 0.004531, 0.037733, 0.064356, 0.099355, 0.162040, 0.185102
-#*# 	-0.175876, -0.143239, -0.079786, -0.027771, 0.013936, 0.058068, 0.081464, 0.115598, 0.174138, 0.206655
-#*# x_count = 10
-#*# y_count = 10
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 30.0
-#*# max_x = 270.0
-#*# min_y = 72.0
-#*# max_y = 270.0
-#*#
-#*# [input_shaper]
-#*# shaper_type_x = mzv
-#*# shaper_freq_x = 98.4
-#*# shaper_type_y = ei
-#*# shaper_freq_y = 83.8
diff --git a/Configure/Printer.cfg/2WD_300_Model_TMC5160.cfg b/Configure/Printer.cfg/2WD_300_Model_TMC5160.cfg
index 44f9f0c..99bf489 100644
--- a/Configure/Printer.cfg/2WD_300_Model_TMC5160.cfg
+++ b/Configure/Printer.cfg/2WD_300_Model_TMC5160.cfg
@@ -187,7 +187,7 @@ hold_current: 0.8                     # Holding current (mA)
 
 [extruder]
 step_pin: EBBCan:gpio18              # Step pin
-dir_pin: !EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
+dir_pin: EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
 enable_pin: !EBBCan:gpio17           # Enable pin, "!" indicates logic inversion
 full_steps_per_rotation: 200         # Number of pulses required for a single motor revolution (1.8 degree motor: 200, 0.9 degree motor: 400)
 microsteps: 16                       # Microsteps setting
@@ -809,34 +809,3 @@ gcode:
   RESPOND TYPE=command MSG='Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta'
   M117 "Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta"
 
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	-0.139892, -0.144629, -0.118855, -0.070701, -0.076458, -0.071339, -0.053576, -0.038063, -0.011182, -0.014896
-#*# 	-0.132548, -0.133431, -0.103451, -0.072262, -0.079405, -0.072497, -0.064156, -0.026437, 0.005466, 0.017700
-#*# 	-0.146372, -0.142454, -0.106913, -0.071101, -0.063307, -0.050075, -0.037609, -0.018205, 0.018473, 0.028662
-#*# 	-0.155715, -0.148744, -0.113136, -0.061509, -0.048525, -0.033687, -0.017161, 0.005627, 0.047608, 0.052961
-#*# 	-0.161258, -0.149702, -0.107886, -0.063084, -0.048428, -0.023841, -0.012515, 0.015900, 0.061648, 0.068628
-#*# 	-0.166502, -0.150839, -0.101034, -0.055136, -0.037974, -0.011766, 0.005559, 0.037965, 0.090939, 0.098797
-#*# 	-0.171896, -0.148182, -0.091620, -0.051904, -0.030924, 0.001613, 0.023529, 0.058473, 0.115695, 0.121967
-#*# 	-0.172872, -0.149272, -0.088044, -0.041005, -0.015835, 0.015057, 0.043967, 0.075708, 0.135351, 0.151476
-#*# 	-0.174137, -0.144846, -0.080953, -0.034735, 0.004531, 0.037733, 0.064356, 0.099355, 0.162040, 0.185102
-#*# 	-0.175876, -0.143239, -0.079786, -0.027771, 0.013936, 0.058068, 0.081464, 0.115598, 0.174138, 0.206655
-#*# x_count = 10
-#*# y_count = 10
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 30.0
-#*# max_x = 270.0
-#*# min_y = 72.0
-#*# max_y = 270.0
-#*#
-#*# [input_shaper]
-#*# shaper_type_x = mzv
-#*# shaper_freq_x = 98.4
-#*# shaper_type_y = ei
-#*# shaper_freq_y = 83.8
diff --git a/Configure/Printer.cfg/2WD_350_Model_TMC2240.cfg b/Configure/Printer.cfg/2WD_350_Model_TMC2240.cfg
index 2416e55..4679fa2 100644
--- a/Configure/Printer.cfg/2WD_350_Model_TMC2240.cfg
+++ b/Configure/Printer.cfg/2WD_350_Model_TMC2240.cfg
@@ -185,7 +185,7 @@ hold_current: 0.8                     # Holding current (mA)
 
 [extruder]
 step_pin: EBBCan:gpio18              # Step pin
-dir_pin: !EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
+dir_pin: EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
 enable_pin: !EBBCan:gpio17           # Enable pin, "!" indicates logic inversion
 full_steps_per_rotation: 200         # Number of pulses required for a single motor revolution (1.8 degree motor: 200, 0.9 degree motor: 400)
 microsteps: 16                       # Microsteps setting
@@ -797,35 +797,3 @@ gcode:
   RESPOND TYPE=command MSG='Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta'
   M117 "Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta"
 
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*#
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	-0.139892, -0.144629, -0.118855, -0.070701, -0.076458, -0.071339, -0.053576, -0.038063, -0.011182, -0.014896
-#*# 	-0.132548, -0.133431, -0.103451, -0.072262, -0.079405, -0.072497, -0.064156, -0.026437, 0.005466, 0.017700
-#*# 	-0.146372, -0.142454, -0.106913, -0.071101, -0.063307, -0.050075, -0.037609, -0.018205, 0.018473, 0.028662
-#*# 	-0.155715, -0.148744, -0.113136, -0.061509, -0.048525, -0.033687, -0.017161, 0.005627, 0.047608, 0.052961
-#*# 	-0.161258, -0.149702, -0.107886, -0.063084, -0.048428, -0.023841, -0.012515, 0.015900, 0.061648, 0.068628
-#*# 	-0.166502, -0.150839, -0.101034, -0.055136, -0.037974, -0.011766, 0.005559, 0.037965, 0.090939, 0.098797
-#*# 	-0.171896, -0.148182, -0.091620, -0.051904, -0.030924, 0.001613, 0.023529, 0.058473, 0.115695, 0.121967
-#*# 	-0.172872, -0.149272, -0.088044, -0.041005, -0.015835, 0.015057, 0.043967, 0.075708, 0.135351, 0.151476
-#*# 	-0.174137, -0.144846, -0.080953, -0.034735, 0.004531, 0.037733, 0.064356, 0.099355, 0.162040, 0.185102
-#*# 	-0.175876, -0.143239, -0.079786, -0.027771, 0.013936, 0.058068, 0.081464, 0.115598, 0.174138, 0.206655
-#*# x_count = 10
-#*# y_count = 10
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 30.0
-#*# max_x = 270.0
-#*# min_y = 72.0
-#*# max_y = 270.0
-#*#
-#*# [input_shaper]
-#*# shaper_type_x = mzv
-#*# shaper_freq_x = 98.4
-#*# shaper_type_y = ei
-#*# shaper_freq_y = 83.8
diff --git a/Configure/Printer.cfg/2WD_350_Model_TMC5160.cfg b/Configure/Printer.cfg/2WD_350_Model_TMC5160.cfg
index 7b24f32..b1d2961 100644
--- a/Configure/Printer.cfg/2WD_350_Model_TMC5160.cfg
+++ b/Configure/Printer.cfg/2WD_350_Model_TMC5160.cfg
@@ -188,7 +188,7 @@ hold_current: 0.8                     # Holding current (mA)
 
 [extruder]
 step_pin: EBBCan:gpio18              # Step pin
-dir_pin: !EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
+dir_pin: EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
 enable_pin: !EBBCan:gpio17           # Enable pin, "!" indicates logic inversion
 full_steps_per_rotation: 200         # Number of pulses required for a single motor revolution (1.8 degree motor: 200, 0.9 degree motor: 400)
 microsteps: 16                       # Microsteps setting
@@ -797,35 +797,3 @@ gcode:
   RESPOND TYPE=command MSG='Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta'
   M117 "Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta"
 
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*#
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	-0.139892, -0.144629, -0.118855, -0.070701, -0.076458, -0.071339, -0.053576, -0.038063, -0.011182, -0.014896
-#*# 	-0.132548, -0.133431, -0.103451, -0.072262, -0.079405, -0.072497, -0.064156, -0.026437, 0.005466, 0.017700
-#*# 	-0.146372, -0.142454, -0.106913, -0.071101, -0.063307, -0.050075, -0.037609, -0.018205, 0.018473, 0.028662
-#*# 	-0.155715, -0.148744, -0.113136, -0.061509, -0.048525, -0.033687, -0.017161, 0.005627, 0.047608, 0.052961
-#*# 	-0.161258, -0.149702, -0.107886, -0.063084, -0.048428, -0.023841, -0.012515, 0.015900, 0.061648, 0.068628
-#*# 	-0.166502, -0.150839, -0.101034, -0.055136, -0.037974, -0.011766, 0.005559, 0.037965, 0.090939, 0.098797
-#*# 	-0.171896, -0.148182, -0.091620, -0.051904, -0.030924, 0.001613, 0.023529, 0.058473, 0.115695, 0.121967
-#*# 	-0.172872, -0.149272, -0.088044, -0.041005, -0.015835, 0.015057, 0.043967, 0.075708, 0.135351, 0.151476
-#*# 	-0.174137, -0.144846, -0.080953, -0.034735, 0.004531, 0.037733, 0.064356, 0.099355, 0.162040, 0.185102
-#*# 	-0.175876, -0.143239, -0.079786, -0.027771, 0.013936, 0.058068, 0.081464, 0.115598, 0.174138, 0.206655
-#*# x_count = 10
-#*# y_count = 10
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 30.0
-#*# max_x = 270.0
-#*# min_y = 72.0
-#*# max_y = 270.0
-#*#
-#*# [input_shaper]
-#*# shaper_type_x = mzv
-#*# shaper_freq_x = 98.4
-#*# shaper_type_y = ei
-#*# shaper_freq_y = 83.8
diff --git a/Configure/Printer.cfg/AWD_300_Model_TMC2240.cfg b/Configure/Printer.cfg/AWD_300_Model_TMC2240.cfg
index 0adef10..24b11bc 100644
--- a/Configure/Printer.cfg/AWD_300_Model_TMC2240.cfg
+++ b/Configure/Printer.cfg/AWD_300_Model_TMC2240.cfg
@@ -221,7 +221,7 @@ hold_current: 0.8                     # Holding current (mA)
 
 [extruder]
 step_pin: EBBCan:gpio18              # Step pin
-dir_pin: !EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
+dir_pin: EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
 enable_pin: !EBBCan:gpio17           # Enable pin, "!" indicates logic inversion
 full_steps_per_rotation: 200         # Number of pulses required for a single motor revolution (1.8 degree motor: 200, 0.9 degree motor: 400)
 microsteps: 16                       # Microsteps setting
@@ -846,34 +846,3 @@ gcode:
   RESPOND TYPE=command MSG='Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta'
   M117 "Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta"
 
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	-0.139892, -0.144629, -0.118855, -0.070701, -0.076458, -0.071339, -0.053576, -0.038063, -0.011182, -0.014896
-#*# 	-0.132548, -0.133431, -0.103451, -0.072262, -0.079405, -0.072497, -0.064156, -0.026437, 0.005466, 0.017700
-#*# 	-0.146372, -0.142454, -0.106913, -0.071101, -0.063307, -0.050075, -0.037609, -0.018205, 0.018473, 0.028662
-#*# 	-0.155715, -0.148744, -0.113136, -0.061509, -0.048525, -0.033687, -0.017161, 0.005627, 0.047608, 0.052961
-#*# 	-0.161258, -0.149702, -0.107886, -0.063084, -0.048428, -0.023841, -0.012515, 0.015900, 0.061648, 0.068628
-#*# 	-0.166502, -0.150839, -0.101034, -0.055136, -0.037974, -0.011766, 0.005559, 0.037965, 0.090939, 0.098797
-#*# 	-0.171896, -0.148182, -0.091620, -0.051904, -0.030924, 0.001613, 0.023529, 0.058473, 0.115695, 0.121967
-#*# 	-0.172872, -0.149272, -0.088044, -0.041005, -0.015835, 0.015057, 0.043967, 0.075708, 0.135351, 0.151476
-#*# 	-0.174137, -0.144846, -0.080953, -0.034735, 0.004531, 0.037733, 0.064356, 0.099355, 0.162040, 0.185102
-#*# 	-0.175876, -0.143239, -0.079786, -0.027771, 0.013936, 0.058068, 0.081464, 0.115598, 0.174138, 0.206655
-#*# x_count = 10
-#*# y_count = 10
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 30.0
-#*# max_x = 270.0
-#*# min_y = 72.0
-#*# max_y = 270.0
-#*#
-#*# [input_shaper]
-#*# shaper_type_x = mzv
-#*# shaper_freq_x = 98.4
-#*# shaper_type_y = ei
-#*# shaper_freq_y = 83.8
diff --git a/Configure/Printer.cfg/AWD_300_Model_TMC5160.cfg b/Configure/Printer.cfg/AWD_300_Model_TMC5160.cfg
index 4dea862..c37e16f 100644
--- a/Configure/Printer.cfg/AWD_300_Model_TMC5160.cfg
+++ b/Configure/Printer.cfg/AWD_300_Model_TMC5160.cfg
@@ -225,7 +225,7 @@ hold_current: 0.8                     # Holding current (mA)
 
 [extruder]
 step_pin: EBBCan:gpio18              # Step pin
-dir_pin: !EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
+dir_pin: EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
 enable_pin: !EBBCan:gpio17           # Enable pin, "!" indicates logic inversion
 full_steps_per_rotation: 200         # Number of pulses required for a single motor revolution (1.8 degree motor: 200, 0.9 degree motor: 400)
 microsteps: 16                       # Microsteps setting
@@ -850,34 +850,3 @@ gcode:
   RESPOND TYPE=command MSG='Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta'
   M117 "Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta"
 
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	-0.139892, -0.144629, -0.118855, -0.070701, -0.076458, -0.071339, -0.053576, -0.038063, -0.011182, -0.014896
-#*# 	-0.132548, -0.133431, -0.103451, -0.072262, -0.079405, -0.072497, -0.064156, -0.026437, 0.005466, 0.017700
-#*# 	-0.146372, -0.142454, -0.106913, -0.071101, -0.063307, -0.050075, -0.037609, -0.018205, 0.018473, 0.028662
-#*# 	-0.155715, -0.148744, -0.113136, -0.061509, -0.048525, -0.033687, -0.017161, 0.005627, 0.047608, 0.052961
-#*# 	-0.161258, -0.149702, -0.107886, -0.063084, -0.048428, -0.023841, -0.012515, 0.015900, 0.061648, 0.068628
-#*# 	-0.166502, -0.150839, -0.101034, -0.055136, -0.037974, -0.011766, 0.005559, 0.037965, 0.090939, 0.098797
-#*# 	-0.171896, -0.148182, -0.091620, -0.051904, -0.030924, 0.001613, 0.023529, 0.058473, 0.115695, 0.121967
-#*# 	-0.172872, -0.149272, -0.088044, -0.041005, -0.015835, 0.015057, 0.043967, 0.075708, 0.135351, 0.151476
-#*# 	-0.174137, -0.144846, -0.080953, -0.034735, 0.004531, 0.037733, 0.064356, 0.099355, 0.162040, 0.185102
-#*# 	-0.175876, -0.143239, -0.079786, -0.027771, 0.013936, 0.058068, 0.081464, 0.115598, 0.174138, 0.206655
-#*# x_count = 10
-#*# y_count = 10
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 30.0
-#*# max_x = 270.0
-#*# min_y = 72.0
-#*# max_y = 270.0
-#*#
-#*# [input_shaper]
-#*# shaper_type_x = mzv
-#*# shaper_freq_x = 98.4
-#*# shaper_type_y = ei
-#*# shaper_freq_y = 83.8
diff --git a/Configure/Printer.cfg/AWD_350_Model_TMC2240.cfg b/Configure/Printer.cfg/AWD_350_Model_TMC2240.cfg
index e6c5008..3208ab5 100644
--- a/Configure/Printer.cfg/AWD_350_Model_TMC2240.cfg
+++ b/Configure/Printer.cfg/AWD_350_Model_TMC2240.cfg
@@ -221,7 +221,7 @@ hold_current: 0.8                     # Holding current (mA)
 
 [extruder]
 step_pin: EBBCan:gpio18              # Step pin
-dir_pin: !EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
+dir_pin: EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
 enable_pin: !EBBCan:gpio17           # Enable pin, "!" indicates logic inversion
 full_steps_per_rotation: 200         # Number of pulses required for a single motor revolution (1.8 degree motor: 200, 0.9 degree motor: 400)
 microsteps: 16                       # Microsteps setting
@@ -829,35 +829,4 @@ gcode:
   RESPOND TYPE=command MSG='Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta'
   M117 "Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta"
 
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*#
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	-0.139892, -0.144629, -0.118855, -0.070701, -0.076458, -0.071339, -0.053576, -0.038063, -0.011182, -0.014896
-#*# 	-0.132548, -0.133431, -0.103451, -0.072262, -0.079405, -0.072497, -0.064156, -0.026437, 0.005466, 0.017700
-#*# 	-0.146372, -0.142454, -0.106913, -0.071101, -0.063307, -0.050075, -0.037609, -0.018205, 0.018473, 0.028662
-#*# 	-0.155715, -0.148744, -0.113136, -0.061509, -0.048525, -0.033687, -0.017161, 0.005627, 0.047608, 0.052961
-#*# 	-0.161258, -0.149702, -0.107886, -0.063084, -0.048428, -0.023841, -0.012515, 0.015900, 0.061648, 0.068628
-#*# 	-0.166502, -0.150839, -0.101034, -0.055136, -0.037974, -0.011766, 0.005559, 0.037965, 0.090939, 0.098797
-#*# 	-0.171896, -0.148182, -0.091620, -0.051904, -0.030924, 0.001613, 0.023529, 0.058473, 0.115695, 0.121967
-#*# 	-0.172872, -0.149272, -0.088044, -0.041005, -0.015835, 0.015057, 0.043967, 0.075708, 0.135351, 0.151476
-#*# 	-0.174137, -0.144846, -0.080953, -0.034735, 0.004531, 0.037733, 0.064356, 0.099355, 0.162040, 0.185102
-#*# 	-0.175876, -0.143239, -0.079786, -0.027771, 0.013936, 0.058068, 0.081464, 0.115598, 0.174138, 0.206655
-#*# x_count = 10
-#*# y_count = 10
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 30.0
-#*# max_x = 270.0
-#*# min_y = 72.0
-#*# max_y = 270.0
-#*#
-#*# [input_shaper]
-#*# shaper_type_x = mzv
-#*# shaper_freq_x = 98.4
-#*# shaper_type_y = ei
-#*# shaper_freq_y = 83.8
+
diff --git a/Configure/Printer.cfg/AWD_350_Model_TMC5160.cfg b/Configure/Printer.cfg/AWD_350_Model_TMC5160.cfg
index 435a8db..f5a764d 100644
--- a/Configure/Printer.cfg/AWD_350_Model_TMC5160.cfg
+++ b/Configure/Printer.cfg/AWD_350_Model_TMC5160.cfg
@@ -225,7 +225,7 @@ hold_current: 0.8                     # Holding current (mA)
 
 [extruder]
 step_pin: EBBCan:gpio18              # Step pin
-dir_pin: !EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
+dir_pin: EBBCan:gpio19               # Direction pin, "!" indicates logic inversion
 enable_pin: !EBBCan:gpio17           # Enable pin, "!" indicates logic inversion
 full_steps_per_rotation: 200         # Number of pulses required for a single motor revolution (1.8 degree motor: 200, 0.9 degree motor: 400)
 microsteps: 16                       # Microsteps setting
@@ -834,35 +834,3 @@ gcode:
   RESPOND TYPE=command MSG='Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta'
   M117 "Follow the remaining instructions here: https://docs.cartographer3d.com/cartographer-probe/advanced-features/temperature-differential-calibration-beta"
 
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*#
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	-0.139892, -0.144629, -0.118855, -0.070701, -0.076458, -0.071339, -0.053576, -0.038063, -0.011182, -0.014896
-#*# 	-0.132548, -0.133431, -0.103451, -0.072262, -0.079405, -0.072497, -0.064156, -0.026437, 0.005466, 0.017700
-#*# 	-0.146372, -0.142454, -0.106913, -0.071101, -0.063307, -0.050075, -0.037609, -0.018205, 0.018473, 0.028662
-#*# 	-0.155715, -0.148744, -0.113136, -0.061509, -0.048525, -0.033687, -0.017161, 0.005627, 0.047608, 0.052961
-#*# 	-0.161258, -0.149702, -0.107886, -0.063084, -0.048428, -0.023841, -0.012515, 0.015900, 0.061648, 0.068628
-#*# 	-0.166502, -0.150839, -0.101034, -0.055136, -0.037974, -0.011766, 0.005559, 0.037965, 0.090939, 0.098797
-#*# 	-0.171896, -0.148182, -0.091620, -0.051904, -0.030924, 0.001613, 0.023529, 0.058473, 0.115695, 0.121967
-#*# 	-0.172872, -0.149272, -0.088044, -0.041005, -0.015835, 0.015057, 0.043967, 0.075708, 0.135351, 0.151476
-#*# 	-0.174137, -0.144846, -0.080953, -0.034735, 0.004531, 0.037733, 0.064356, 0.099355, 0.162040, 0.185102
-#*# 	-0.175876, -0.143239, -0.079786, -0.027771, 0.013936, 0.058068, 0.081464, 0.115598, 0.174138, 0.206655
-#*# x_count = 10
-#*# y_count = 10
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 30.0
-#*# max_x = 270.0
-#*# min_y = 72.0
-#*# max_y = 270.0
-#*#
-#*# [input_shaper]
-#*# shaper_type_x = mzv
-#*# shaper_freq_x = 98.4
-#*# shaper_type_y = ei
-#*# shaper_freq_y = 83.8