-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathboard_ultralumic.cfg
180 lines (156 loc) · 3.1 KB
/
board_ultralumic.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
##################################
# VOLUMIC ULTRALUMIC configuration
##################################
# Slot X(X) pour moteur X
[stepper_x]
step_pin: PD0
dir_pin: PD1
enable_pin: !PA15
rotation_distance: 40
endstop_pin: ^!PB19
position_endstop: 0
# Slot Yr(Y) pour moteur Y1 gauche
[stepper_y]
step_pin: PB26
dir_pin: PA14
enable_pin: !PC1
rotation_distance: 40
endstop_pin: ^!PB18
# Slot Ya/Zag(Z1) pour moteur Y2 droit
[stepper_y1]
step_pin: !PC3
dir_pin: !PC2
enable_pin: !PC5
rotation_distance: 40
#endstop_pin: ^!PA6
# Slot Zad(Z2) pour moteur Z1 avant gauche
[stepper_z]
step_pin: PC7
dir_pin: PC6
enable_pin: !PC8
rotation_distance: 4.0442666666666666666664
endstop_pin: probe:z_virtual_endstop
position_min: -8
# Slot Zg(E0) pour moteur Z2 arrière gauche
[stepper_z1]
step_pin: PC16
dir_pin: PC17
enable_pin: !PC15
rotation_distance: 4.0442666666666666666664
endstop_pin: probe:z_virtual_endstop
# Slot Zd(Z4) pour moteur Z3 arrière droit
[stepper_z2]
step_pin: PC19
dir_pin: PC4
enable_pin: !PC18
rotation_distance: 4.0442666666666666666664
endstop_pin: probe:z_virtual_endstop
# Slot E0 pour moteur Z4 avant droit
[stepper_z3]
step_pin: PA19
dir_pin: PC9
enable_pin: !PA20
rotation_distance: 4.0442666666666666666664
endstop_pin: probe:z_virtual_endstop
# Slot E1 pour moteur E0 extrudeur
[extruder]
step_pin: PC13
dir_pin: PC14
enable_pin: !PC12
rotation_distance: 8.7671232876712328767123287671233
filament_diameter: 1.75
heater_pin: PC28
sensor_type: PT100 INA826
sensor_pin: PB20
min_temp: 2
max_temp: 350
min_extrude_temp: 10
pressure_advance: 0.0375
pressure_advance_smooth_time: 0.040
Max_extrude_only_distance: 250
# Peripheral configurations
[filament_switch_sensor Detecteur_filament]
switch_pin: ^PD4
pause_on_runout: True
runout_gcode: G0 E-200 F400
insert_gcode:
G92 E0.0
G0 E25 F150
{% if not printer.pause_resume.is_paused %}
M109 S220
{% endif %}
M83
G92 E0.0
G0 E150 F300
G92 E0.0
M82
{% if not printer.pause_resume.is_paused %}
M84
{% endif %}
[heater_bed]
heater_pin: PB25
sensor_type: Generic 3950
sensor_pin: PA16
min_temp: 0
max_temp: 150
[fan]
pin: PC25
[heater_fan Extrudeur]
pin: PC24
#tachometer_pin: PC15
heater_temp: 40
max_power: 1
[controller_fan Electronique]
pin: PC21
idle_timeout: 60
[fan_generic _Capot]
pin: PC23
[fan_generic _Alimentation]
pin: !PC22
hardware_pwm: false
max_power: 1
shutdown_speed: 1
[temperature_sensor Alimentation]
sensor_type: PT100 INA826
sensor_pin: PA2
min_temp: 0
max_temp: 60
gcode_id: power
[temperature_sensor Protection]
sensor_type: Generic 3950
sensor_pin: PA24
min_temp: 0
max_temp: 65
gcode_id: prot
[temperature_sensor Chambre]
sensor_type: Generic 3950
sensor_pin: PA22
min_temp: 0
max_temp: 60
gcode_id: room
[led Eclairage_LEDs]
red_pin:PD7
green_pin:PD8
blue_pin:PB27
hardware_pwm: True
initial_RED: 0.0
initial_GREEN: 1.0
initial_BLUE: 0.0
[output_pin Palpeur]
pin: PD3
value: 0
[probe]
pin: !PD5
deactivate_on_each_sample: False
speed: 5.0
activate_gcode:
Palpeur_ON
G4 P500
deactivate_gcode:
Palpeur_OFF
[gcode_button stop_button]
pin: ^!PB12
press_gcode: {action_emergency_stop()}
#[gcode_button Porte]
#pin: ^!PD10
#press_gcode: PAUSE