diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index b0465778b7..3398704d1b 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -143,7 +143,7 @@
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+#define CUSTOM_MACHINE_NAME "Snapmaker J1 VH"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -683,7 +683,7 @@
 #endif // PIDTEMPCHAMBER
 
 #if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
-  #define PID_DEBUG             // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
+  //#define PID_DEBUG             // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
   //#define PID_OPENLOOP          // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   #define PID_FUNCTIONAL_RANGE 15 // If the temperature difference between the target temperature and the actual temperature
@@ -1297,8 +1297,8 @@
 
 // @section extruder
 
-#define DISABLE_E false             // Disable the extruder when not stepping
-// #define DISABLE_INACTIVE_EXTRUDER   // Keep only the active extruder enabled
+#define DISABLE_E false             // Disable the extruder when not stepping QQQ
+#define DISABLE_INACTIVE_EXTRUDER   // Keep only the active extruder enabled
 
 // @section machine
 
@@ -1424,7 +1424,7 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
   #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 28447f135a..a2f674c1a1 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -736,7 +736,7 @@
   #define DEFAULT_DUPLICATION_X_OFFSET 100
 
   // Default action to execute following M605 mode change commands. Typically G28X to apply new mode.
-  //#define EVENT_GCODE_IDEX_AFTER_MODECHANGE "G28X"
+  #define EVENT_GCODE_IDEX_AFTER_MODECHANGE "G28X"
 #endif
 
 // Activate a solenoid on the active extruder with M380. Disable all with M381.
diff --git a/Marlin/Version.h b/Marlin/Version.h
index 23ee5d79b8..df5b9ed888 100644
--- a/Marlin/Version.h
+++ b/Marlin/Version.h
@@ -41,12 +41,12 @@
  * here we define this default string as the date where the latest release
  * version was tagged.
  */
-#define STRING_DISTRIBUTION_DATE "2023-11-18"
+#define STRING_DISTRIBUTION_DATE "2024-03-16"
 
 /**
  * Defines a generic printer name to be output to the LCD after booting Marlin.
  */
-#define MACHINE_NAME "Snapmaker J1s VH_v0.0.1"
+#define MACHINE_NAME "Snapmaker J1s VH_v0.0.2"
 
 /**
  * The SOURCE_CODE_URL is the location where users will find the Marlin Source