diff --git a/boards/nxp/mimxrt1060_evk/CMakeLists.txt b/boards/nxp/mimxrt1060_evk/CMakeLists.txt
index 2778972698b482..29263b8b55596f 100644
--- a/boards/nxp/mimxrt1060_evk/CMakeLists.txt
+++ b/boards/nxp/mimxrt1060_evk/CMakeLists.txt
@@ -1,5 +1,5 @@
 #
-# Copyright 2018-2022 NXP
+# Copyright 2018-2022, 2025 NXP
 #
 # SPDX-License-Identifier: Apache-2.0
 #
@@ -12,7 +12,7 @@ endif()
 
 if(CONFIG_NXP_IMXRT_BOOT_HEADER)
   zephyr_library()
-  if(${BOARD_REVISION} STREQUAL "B")
+  if((${BOARD_REVISION} STREQUAL "B") OR (${BOARD_REVISION} STREQUAL "C"))
     set(FLASH_CONF evkbmimxrt1060_flexspi_nor_config.c)
     set(BOARD_NAME evkbmimxrt1060)
   elseif(CONFIG_DT_HAS_NXP_IMX_FLEXSPI_NOR_ENABLED)
diff --git a/boards/nxp/mimxrt1060_evk/board.cmake b/boards/nxp/mimxrt1060_evk/board.cmake
index e6748688a78999..b9926a99a3eb12 100644
--- a/boards/nxp/mimxrt1060_evk/board.cmake
+++ b/boards/nxp/mimxrt1060_evk/board.cmake
@@ -14,7 +14,7 @@ board_runner_args(pyocd "--target=mimxrt1060")
 board_runner_args(jlink "--device=MIMXRT1062xxx6A")
 board_runner_args(linkserver  "--device=MIMXRT1062xxxxA:EVK-MIMXRT1060")
 
-if(("${BOARD_QUALIFIERS}" MATCHES "qspi") OR ("${BOARD_REVISION}" STREQUAL "B"))
+if(("${BOARD_QUALIFIERS}" MATCHES "qspi") OR ("${BOARD_REVISION}" STREQUAL "B") OR ("${BOARD_REVISION}" STREQUAL "C"))
   board_runner_args(jlink "--loader=BankAddr=0x60000000&Loader=QSPI")
 elseif ("${BOARD_QUALIFIERS}" MATCHES "hyperflash")
   board_runner_args(jlink "--loader=BankAddr=0x60000000&Loader=HyperFlash")
diff --git a/boards/nxp/mimxrt1060_evk/board.yml b/boards/nxp/mimxrt1060_evk/board.yml
index 30a5701b1feb7e..6ea1376ab869c8 100644
--- a/boards/nxp/mimxrt1060_evk/board.yml
+++ b/boards/nxp/mimxrt1060_evk/board.yml
@@ -9,7 +9,8 @@ boards:
           - name: "hyperflash"
     revision:
       format: "letter"
-      default: "A"
+      default: "C"
       revisions:
         - name: "A"
         - name: "B"
+        - name: "C"
diff --git a/boards/nxp/mimxrt1060_evk/doc/index.rst b/boards/nxp/mimxrt1060_evk/doc/index.rst
index 940ca2a593ecfc..372aaea085e566 100644
--- a/boards/nxp/mimxrt1060_evk/doc/index.rst
+++ b/boards/nxp/mimxrt1060_evk/doc/index.rst
@@ -316,8 +316,28 @@ The MIMXRT1060 SoC has eight UARTs. ``LPUART1`` is configured for the console,
 ``LPUART3`` for the Bluetooth Host Controller Interface (BT HCI), and the
 remaining are not used.
 
-Board Targets
-*************
+Board Revisions and Targets
+***************************
+
+There are three revisions of this board.
+
+Rev A:
+
+* Initial version
+
+Rev B:
+
+* adds the M.2 connector for Wi-Fi/BLE
+* adds audio expansion connector J23
+* USER LED1 changed to GPIO1 pin 8
+
+Rev C:
+
+* Replaces audio codec WM8960(EOL) to WM8962
+* Replaces 32.768 KHz oscillator from ASH7K-32.768KHz-T(EOL)to ASH7KW-32.768KHZ-L-T
+* Replaces motion sensor from FXOS8700CQ(EOL) to FXLS8974CFR3
+* Re-assigns Bluetooth Audio PCM with dedicated I2S2
+* Re-assigns Bluetooth interface UART_CTS, UART_RTS to hardware PIN
 
 This board has two variants that can be targeted,
 depending on which flash to set as ``zephyr,flash``:
@@ -387,10 +407,28 @@ Flashing
 
 Here is an example for the :zephyr:code-sample:`hello_world` application.
 
-.. zephyr-app-commands::
-   :zephyr-app: samples/hello_world
-   :board: mimxrt1060_evk//qspi
-   :goals: flash
+.. tabs::
+
+   .. group-tab:: i.MX RT1060 Rev A
+
+      .. zephyr-app-commands::
+         :zephyr-app: samples/hello_world
+         :board: mimxrt1060_evk@A//qspi
+         :goals: flash
+
+   .. group-tab:: i.MX RT1060 Rev B
+
+      .. zephyr-app-commands::
+         :zephyr-app: samples/hello_world
+         :board: mimxrt1060_evk@B//qspi
+         :goals: flash
+
+   .. group-tab:: i.MX RT1060 Rev C (default)
+
+      .. zephyr-app-commands::
+         :zephyr-app: samples/hello_world
+         :board: mimxrt1060_evk@C//qspi
+         :goals: flash
 
 Open a serial terminal, reset the board (press the SW9 button), and you should
 see the following message in the terminal:
@@ -405,10 +443,29 @@ Debugging
 
 Here is an example for the :zephyr:code-sample:`hello_world` application.
 
-.. zephyr-app-commands::
-   :zephyr-app: samples/hello_world
-   :board: mimxrt1060_evk//qspi
-   :goals: debug
+.. tabs::
+
+   .. group-tab:: i.MX RT1060 Rev A
+
+      .. zephyr-app-commands::
+         :zephyr-app: samples/hello_world
+         :board: mimxrt1060_evk@A//qspi
+         :goals: debug
+
+   .. group-tab:: i.MX RT1060 Rev B
+
+      .. zephyr-app-commands::
+         :zephyr-app: samples/hello_world
+         :board: mimxrt1060_evk@B//qspi
+         :goals: debug
+
+   .. group-tab:: i.MX RT1060 Rev C (default)
+
+      .. zephyr-app-commands::
+         :zephyr-app: samples/hello_world
+         :board: mimxrt1060_evk@C//qspi
+         :goals: debug
+
 
 Open a serial terminal, step through the application in your debugger, and you
 should see the following message in the terminal:
diff --git a/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_B.yaml b/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_B.yaml
index 5c9f42d5ef717a..c46f4ceba9ae97 100644
--- a/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_B.yaml
+++ b/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_B.yaml
@@ -15,20 +15,20 @@ toolchain:
 ram: 32768
 flash: 8192
 supported:
+  - adc
   - arduino_gpio
   - arduino_i2c
   - arduino_serial
   - arduino_spi
+  - can
   - counter
   - display
+  - dma
   - gpio
   - i2c
   - netif:eth
   - sdhc
   - spi
   - usb_device
-  - dma
-  - can
   - watchdog
-  - adc
 vendor: nxp
diff --git a/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_C.overlay b/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_C.overlay
new file mode 100644
index 00000000000000..284679eaa9f28f
--- /dev/null
+++ b/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_C.overlay
@@ -0,0 +1,15 @@
+/*
+ * Copyright (c) 2022, Whisper.ai
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/* FLEXPWM not routed to LED on this EVK */
+&flexpwm2_pwm3 {
+	status = "disabled";
+};
+
+&green_led {
+	gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+	label = "User LED1";
+};
diff --git a/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_C.yaml b/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_C.yaml
new file mode 100644
index 00000000000000..94394b3b84e91d
--- /dev/null
+++ b/boards/nxp/mimxrt1060_evk/mimxrt1060_evk_mimxrt1062_qspi_C.yaml
@@ -0,0 +1,34 @@
+#
+# Copyright (c) 2022, Whisper.ai
+#
+# SPDX-License-Identifier: Apache-2.0
+#
+
+identifier: mimxrt1060_evk@C/mimxrt1062/qspi
+name: NXP MIMXRT1060-EVKC
+type: mcu
+arch: arm
+toolchain:
+  - zephyr
+  - gnuarmemb
+  - xtools
+ram: 32768
+flash: 8192
+supported:
+  - adc
+  - arduino_gpio
+  - arduino_i2c
+  - arduino_serial
+  - arduino_spi
+  - can
+  - counter
+  - display
+  - dma
+  - gpio
+  - i2c
+  - netif:eth
+  - sdhc
+  - spi
+  - usb_device
+  - watchdog
+vendor: nxp