mvebu: add support for Fortinet FortiGate 30E

Fortinet FortiGate 30E (FG-30E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 1 GiB (4x Micron MT41K256M8DA-125, "D9PSH")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 5x 10/100/1000 Mbps
  - Switch     : Marvell 88E6176
- LEDs/Keys    : 16x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Modex 5557-02R

Flash instruction using initramfs image:

 1. Power on FG-30E and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "r" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:CE (board-info, 0xd880 (hex))
WAN   : 70:4C:A5:xx:xx:CF
LAN 1 : 70:4C:A5:xx:xx:D0
LAN 2 : 70:4C:A5:xx:xx:D1
LAN 3 : 70:4C:A5:xx:xx:D2
LAN 4 : 70:4C:A5:xx:xx:D3

Signed-off-by: INAGAKI Hiroshi <[email protected]>

target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network

@@ -18,12 +18,7 @@ mvebu_setup_interfaces()
 	cznic,turris-omnia)
 		ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3 lan4" "eth2"
 		;;
-	fortinet,fg-50e)
-		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "eth1 eth2"
-		;;
-	iptime,nas1dual)
-		ucidef_set_interface_lan "eth0 eth1" "dhcp"
-		;;
+	fortinet,fg-30e|\
 	linksys,wrt1200ac|\
 	linksys,wrt1900ac-v1|\
 	linksys,wrt1900ac-v2|\
@@ -32,6 +27,12 @@ mvebu_setup_interfaces()
 	linksys,wrt32x)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
 		;;
+	fortinet,fg-50e)
+		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "eth1 eth2"
+		;;
+	iptime,nas1dual)
+		ucidef_set_interface_lan "eth0 eth1" "dhcp"
+		;;
 	marvell,a385-db-ap)
 		ucidef_set_interfaces_lan_wan "eth0 eth1" "eth2"
 		;;

target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh

@@ -52,6 +52,7 @@ platform_do_upgrade() {
 	solidrun,clearfog-pro-a1)
 		legacy_sdcard_do_upgrade "$1"
 		;;
+	fortinet,fg-30e|\
 	fortinet,fg-50e)
 		fortinet_do_upgrade "$1"
 		;;

target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-30e.dts

@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "armada-385-fortinet-fg-x0e.dtsi"
+
+/ {
+	model = "Fortinet FortiGate 30E";
+	compatible = "fortinet,fg-30e", "marvell,armada385", "marvell,armada380";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1GB */
+	};
+};
+
+&gpio_leds {
+	led-14 {
+		label = "amber:speed_wan";
+		gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+		color = <LED_COLOR_ID_AMBER>;
+		linux,default-trigger = "mv88e6xxx-1:00:100Mbps";
+	};
+
+	led-15 {
+		label = "green:speed_wan";
+		gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		color = <LED_COLOR_ID_GREEN>;
+		linux,default-trigger = "mv88e6xxx-1:00:1Gbps";
+	};
+};
+
+&pinctrl {
+	pmx_switch_pins: switch-pins {
+		marvell,pins = "mpp19";
+		marvell,function = "gpio";
+	};
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>, <&pmx_switch_pins>;
+
+	/* Marvell 88E6176 */
+	switch@2 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x2>;
+		reset-gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "wan";
+				nvmem-cells = <&macaddr_bdinfo_d880>;
+				nvmem-cell-names = "mac-address";
+				mac-address-increment = <1>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan4";
+				nvmem-cells = <&macaddr_bdinfo_d880>;
+				nvmem-cell-names = "mac-address";
+				mac-address-increment = <5>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan3";
+				nvmem-cells = <&macaddr_bdinfo_d880>;
+				nvmem-cell-names = "mac-address";
+				mac-address-increment = <4>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan2";
+				nvmem-cells = <&macaddr_bdinfo_d880>;
+				nvmem-cell-names = "mac-address";
+				mac-address-increment = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan1";
+				nvmem-cells = <&macaddr_bdinfo_d880>;
+				nvmem-cell-names = "mac-address";
+				mac-address-increment = <2>;
+			};
+
+			port@6 {
+				reg = <6>;
+				ethernet = <&eth0>;
+				phy-connection-type = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};